> Hard Drive
> Swapping Secondary HD's Has Messed Up The BIOS
Swapping Secondary HD's Has Messed Up The BIOS
Also, you mentioned something that concerned me; formatting the drive. ect... A quick note about hard drives. Reply Jakey on October 2, 2007 at 11:08 am I have no experience whatsoever and didnt even know the difference bewteen the cables but you have saved me 50.00 possibly more check over here
The BIOS should be able to see both drives pure and simple. So, here is a link that may help further your quest:http://www.buildorbuy.org/datarecovery.htmlAlso, I like to recommend checking with the Ontrack people they offer some solutions, too. Reply Kallon on July 13, 2014 at 5:28 pm I know this is a while from original comment but couldnt you just remove the other hard drives and make the one angry in OHIO Reply Nepe on March 8, 2009 at 5:25 am I installed my original HD in the second bay as a slave and was able to access my files. navigate to this website
How To Boot From Second Hard Drive Windows 7
The metal the case is built from is thicker than average so the screws I have do not reach to try and install it that way. My original X58/i7-920 system has been rebuilt as the playground for all of my experimenting. Isn't XP great?!! 5 3/7/2002 (11:04 pm) by admin Staff admin (24314 Posts) To install XP/2000 from Dos, locate your i386 folder and run 'winnt.exe'.
- Shut the machine off, pull the power plug out of the back of the old computer, and remove the computer access panel or cover.
- I completed changing the system over to appliance mode - removed the plug-in disk adapters, installed some data disks, and, most important, installed a 240GB BP4 mSATA SSD with the contents
- The problem with that is if you ever need to re-load Windows (or the original brand name software installation) from scratch, you lose everything on the partition Windows was installed on,
- The only way to get the computer to run Windows XP is to turn OFF the new drive which of course defeats the issue.
the drive is working properly. Reply JP on August 10, 2007 at 5:06 pm I'm trying to add a second SATA hard drive to my Dell. Your computer should see and read your drivejust fine. Install Old Hard Drive In New Computer Only windows is not working anymore what you like to do about that???
when I type in setup and my cd-rom drive prompt, a message comes up that says windows is needed to run that program. Two Hard Drives Two Operating Systems Some BIOSes allow you to pick which drive you want to boot from, so that you could do what you ask by just changing the setting in the BIOS. There are companies like http://www.mrbios.com/ but you may be not happy since such booting is not only an issue in the initial boot, but if the OS in question is coded https://www.cnet.com/forums/discussions/bios-upgrade-to-boot-second-hard-drive-17504/ Electrical problems can happen instantly, without warning.
Any hard drive should get a letter allias before the CD drives. Moving Hard Drive To New Computer Windows 10 Reply curt on July 12, 2009 at 9:49 am You probably already figured it out…. Physically swapping hard drives just doesn't cut it - too time consuming and damage-prone. They use an ACX_100 chip from Memorex who apparently won?t release a binary driver for Linux and all the hacks and alleged roll-ur-own drivers have yet to get me a Linux
Two Hard Drives Two Operating Systems
This is because, for an IDE drive, it matters. Joshcore, if you are blindly defending your precious website PC Mech, then please, at least have a decent reason to do so. How To Boot From Second Hard Drive Windows 7 Now, with the power disconnected, attach the drive. Swapping Hard Drives Between Computers rd400d77 by jakharve / March 29, 2004 6:14 PM PST In reply to: Re:Re:2nd reply..
I forgot about formatting it. http://ipbillboard.com/hard-drive/swapping-out-hard-drives.html I want a general and permanent increase in capability. Reply mark on December 18, 2008 at 12:29 pm working on a computer with two hard drives. If you believe this post is offensive or violates the CNET Forums' Usage policies, you can report it below (this will not automatically remove the post). How To Add An Old Hard Drive To A New Computer
Wow again thank you Reply Eric on October 13, 2009 at 11:16 pm Great instructions. Antec EA-430 Disks.................. I believe this is causing all sorts of conflicts right now as it will not load. http://ipbillboard.com/hard-drive/swapping-hdd-with-os-between-machines.html Too bad they messed up the BIOS.
Also please exercise your best judgment when posting in the forums--revealing personal information such as your e-mail address, telephone number, and address is not recommended. Dual Boot Two Hard Drives By the four sentence, you are assuming that everyone reading this will understand what ‘jumpers' are. Of course, it must have a boot block and a viable OS on it.
can some one please help me.
Flag Permalink This was helpful (0) Collapse - Difference Bothers You? Reply Mark barbee on August 31, 2009 at 7:25 pm Here's one for ya. If you are using SATA, your motherboard likely comes with enough SATA ports. Transfer Hard Drive To New Computer Without Reinstalling Windows If you are confident in yourself and would like to save the money a computer guy would charge to do it, go ahead and do it yourself.
Sorry I was not clear before.How do I change the boot order? Reply Ravenwolfvoyager on September 29, 2007 at 1:14 pm Great article, I really appreciate the simplicity involved and the easy to follow instructions. Makes sense, but I just didn't think about it. have a peek at these guys How do i clone the 40gig drive onto the 250gig without formatting the 250gig.
It is a standard bios with ahci enabled Back to top #7 waldojim42 waldojim42 Members 159 posts OFFLINE Gender:Not Telling Location:Texas Local time:05:31 PM Posted 15 January 2014 - 12:49 It?s easy to lose track of which drive is which. Now that SATA is becoming much more prevalent than IDE, it is becoming a lot less likely that you will need to worry about jumpers during this process.Before installation, inspect the I assume you want to do this to keep access to your data rather than to run programmes from it.