> How To
> Startup Configuration
The prompting will depend on how much information you provide in the copy command and the current setting of the file prompt global configuration command. However, the show running-config command will continue to be supported as a command alias for the more system:running-config command. Commands are parsed (translated and executed) by the Cisco IOS software when the system is booted (from the startup-config file) or when you enter commands at the CLI in a configuration When you save the configuration using the copy system:running-config nvram:startup-config command, the router saves a complete version of the configuration file to the location specified by the CONFIG_FILE environment variable and have a peek here
Router# configure terminal !parser cache is disabled Router(config)# no parser cache !configuration file is loaded into the running configuration Router# copy slot0:acl_list running-config . . . Enter the enable command to enter enable mode. The default network configuration file is network-confg. For example, you might perform this task to back up a current configuration file to a server before changing its contents, thereby allowing you to later restore the original configuration file http://www.howtogeek.com/74523/how-to-disable-startup-programs-in-windows/
How To Disable Startup Programs Windows 10
Yes No Feedback Let Us Help Open a Support Case (Requires a Cisco Service Contract) Related Support Community Discussions Share Information For Small Business Midsize Business Service Provider Industries Automotive Consumer See the "Specifying the CONFIG_FILE Environment Variable on Class A Flash File Systems" section for more information. To modify the CONFIG_FILE environment variable, use the boot config command and then save your changes by issuing the copy system:running-config nvram:startup-config command.
- Sign in to report inappropriate content.
- You can also refer to the MGX 8850 Wide Area Switch Command Reference and MGX 8850 Wide Area Switch Installation and Configuration documents for information about the commands you can use
- Router#show running-config Displays the contents of the running configuration file. (Command alias for the more system:running-config command.) Router#show startup-config Displays the contents of the startup configuration file. (Command alias for the
- Enter enable and the enable password to put the router into enabled mode. 4.
- You may want to perform this function for one of the following reasons: •To restore a backed-up configuration file. •To use the configuration file for another router.
To compress configuration files, use the following commands beginning in global configuration mode: Command Purpose Step1 Router(config)#service compress-config Specifies that the configuration file be compressed. The pipe (|) is required. | exclude string (Optional) Exclude from the output any line that matches the specified string. Statistics are stored since the initialization of the system, or since the last time the parser cache was cleared. Windows 7 Startup Folder You set the CONFIG_FILE environment variable in the current running memory when you use the bootconfig command.
The service compress-config global configuration command works only if you have CiscoIOS software Release 10 or later release boot ROMs. How To Disable Startup Programs Windows 7 When booting from a network server, routers ignore routing information, static IP routes, and bridging information. interface Serial0:23 description PRI to ADTRAN (#4444150) ip unnumbered Loopback0 encapsulation ppp dialer rotary-group 0 isdn switch-type primary-dms100 isdn incoming-voice modem isdn calling-number 4444150 peer default ip address pool new_pool ppp Location of Configuration Files Configuration files are stored in the following locations: •The running configuration is stored in RAM. •On all platforms except the Class A Flash file system platforms, the
Table33 describes the key output fields: Table33 show parser statistics Output Fields Last configuration file parsed: Displays statistics on the last configuration file copied into the running configuration (at startup or How To Stop Programs From Running At Startup Windows 7 OK Erase flash device before writing? [confirm] Flash contains files. Usage Guidelines The Parser Cache feature optimizes the parsing (translation and execution) of Cisco IOS software configuration command lines by remembering how to parse recently encountered command lines, decreasing the time It differs when the configuration for an interface is derived from a template, a dialer interface, or some per-user configuration.
How To Disable Startup Programs Windows 7
map-class frame-relay cir70 no frame-relay adaptive-shaping frame-relay priority-group 2 ! https://supportforums.cisco.com/discussion/10766991/where-startup-config-stored To copy configuration information on a TFTP network server, use the following commands in the EXEC mode, as needed: Command Purpose Router#copy system:running-config tftp:[[[//location]/directory]/filename] Copies the running configuration file to a How To Disable Startup Programs Windows 10 The password set by the ip ftp password command, if the command is configured. 3. Startup Programs Windows 8 Understanding the FTP Username and Password The FTP protocol requires a client to send a remote username and password on each FTP request to a server.
Examples The following example sets the host filename to wilma-confg at address 192.168.7.19: Router(config)# boot host tftp://192.168.7.19/usr/local/tftpdir/wilma-confg Router(config)# service config Related Commands Command Description boot network Specifies the remote location and navigate here If the Cisco IOS software cannot resolve its hostname, the default host configuration file is router-confg. The router sends the first valid password in the following list: 1. How-To Geek Articles l l What Is Android TV, and Which Android TV Box Should I Buy? How To Make A Program Run On Startup Windows 10
To obtain a list of commands that begin with a particular character sequence, type in those characters followed immediately by the question mark (?). Then it copies the configuration file named host2-confg from the netadmin1 directory on the remote server with an IP address of 172.16.101.101 to the startup configuration. Usage Guidelines The show parser statistics command displays two sets of data: •The number of commands in the configuration file that was last copied into the running configuration, and the time Check This Out The username specified in the boot network command, if a username is specified. 2.
To restore the host configuration filename to the default, use the no form of this command. Startup Config Cisco Include the username in the copy EXEC command if you want to specify a username for that copy operation only. Step4 Router(config)#end (Optional) Exits global configuration mode.
The show derived-config command displays all the commands that apply to an interface.
Copying a Configuration File from the Router to an rcp Server To copy a startup configuration file or a running configuration file from the router to an rcp server, use the After you have issued the copy EXEC command, you may be prompted for additional information or for confirmation of the action. Because file management for Flash memory, such as optimizing free space, is not done automatically, you must pay close attention to available Flash memory. Add Program To Startup Windows 7 A good practice is always back it up to a common network drive like TFTP/FTP server.Regards,jerry See correct answer in context 1 2 3 4 5 Overall Rating: 5 (1 ratings)
The startup configuration file cannot be restored once it has been deleted. Steve 86,071 views 4:14 How to set your computer to run a program at startup on Windows 7 - Duration: 3:45. For configuration information and examples, refer to the "Managing Configuration Files" chapter in the Release12.2 CiscoIOS Configuration Fundamentals Configuration Guide. http://ipbillboard.com/how-to/startup-from-run.html Almost every configuration command also has a no form.
To restore the network configuration filename to the default, use the no form of this command. Autoplay When autoplay is enabled, a suggested video will automatically play next. The default host configuration file is host-confg, where host is the hostname of the router. Router#more file-url Displays the contents of a specified file.
Copying a Configuration File from the rcp Server to the Router To copy a configuration file from an rcp server to the running configuration or startup configuration, use the following commands Command Modes Global configuration Command History Release Modification 10.0 This command was introduced. show parser statistics Syntax Description This command has no arguments or keywords. The password set by the ip ftp password command, if the command is configured. 3.
For a complete description of the configuration file management commands in this chapter, refer to the "Configuration File Management Commands" chapter in the Release12.2 CiscoIOS Configuration Fundamentals Command Reference.